Home › Leaking Tap Repairs in Ringwood

Taps and mixers · Ringwood VIC 3134

Leaking Tap Repairs in Ringwood

A tap that drips day and night wastes water and slowly stains the basin. We repair and replace taps and mixers across Ringwood, usually in a single visit. Ring 03 9088 4157.

Licensed plumbers Ringwood 3134 Price settled up front After-hours help

Plumber fitting a new gooseneck mixer tap at a stone kitchen bench in an apartment

Why taps drip

Most taps in Ringwood homes fall into two groups.

Older two-handle taps use a rubber washer that presses against a seat to stop the flow. Over time the washer hardens, splits or wears, and the seat can become pitted. Water then seeps past even when the handle is firmly closed. Spindles can also wear, causing leaks around the handle rather than from the spout.

Mixer taps use a ceramic cartridge. Grit, scale or wear can damage the cartridge discs, leading to drips from the spout or leaks around the base. Cartridges also fail in ways that make the tap stiff, noisy or hard to adjust.

What a slow drip costs

A tap that drips steadily can waste many litres a week. Beyond the water bill, constant dripping can stain basins and sinks, and in a hot tap it wastes the energy used to heat the water. On a unit site with a shared meter, the waste may be spread across neighbours' bills too.

How we repair taps

Two-handle taps

We isolate the water, take the tap apart, and replace the washer and O-rings. If the seat is damaged, we re-face it so the new washer seals properly. If the spindle is worn, we replace the jumper valve or the whole spindle assembly.

Mixers

We remove the handle and replace the cartridge with the correct part for your brand and model. For unusual or older mixers where parts are no longer available, we talk through replacement options.

Leaks under the sink

Sometimes the drip is not from the spout but from connections underneath: braided hoses, isolation valves or the tap's own fittings. We check and fix those too.

Replacing tapware

Replacement makes sense when:

  • Parts are no longer available for an older tap
  • The tap body is corroded or cracked
  • You are updating the look of a kitchen, bathroom or laundry
  • You want a different style, such as a gooseneck kitchen mixer or a wall-mounted bath set

We can supply tapware or fit a set you have chosen. We check that it suits the existing holes, connections and water pressure, and that it carries the right WaterMark certification for use in Australia.

Kitchen, bathroom, laundry and outdoor taps

  • Kitchen mixers take a lot of use and are often the first to drip. Pull-out sprays have hoses that can wear too.
  • Basin and shower taps in older bathrooms may be original two-handle sets with worn washers.
  • Laundry taps with washing machine hoses attached can fail with a sudden leak. We often replace washing machine taps with quarter-turn valves.
  • Garden taps can drip, leak at the stem or crack in frosty weather. We repair or replace them and can add backflow prevention where needed.

Shower mixers in the wall

A dripping shower head usually means the wall mixer's cartridge or washers have worn. We can usually service it through the front plate without removing tiles. If the body inside the wall has failed, we explain the options.

Water pressure and tap wear

High water pressure wears out washers and cartridges faster, and can make taps bang when they are closed. If your taps drip repeatedly, we can test the pressure and fit a pressure limiting valve if needed.

Tips to make taps last

  • Close taps gently rather than forcing them
  • Clean aerators to remove grit and scale
  • Fix drips early before seats are damaged
  • Replace braided hoses under sinks every ten years or so

Laundry and dishwasher valves

Washing machine taps and dishwasher valves are under constant pressure and often forgotten. A cracked tap body or worn spindle can let go without warning. We can swap old screw-down taps for quarter-turn valves that are easier to turn off quickly and less prone to leaking.

Taps that are hard to turn

A stiff handle on an older tap usually means a worn or scaled spindle, and a stiff mixer usually means a cartridge on its way out. Forcing either can strip the parts or snap a spindle, so it is worth fixing before it fails completely. We clean, grease or replace the parts so the tap turns smoothly again.

Outdoor taps and backflow

Garden taps used with hoses, sprays and fertiliser attachments can let contaminated water flow back into the supply. A simple vacuum breaker or hose-connection backflow device prevents it, and we can fit one when we repair the tap.

Ring us

For leaking tap repairs in Ringwood, ring 03 9088 4157.

The standard

Every taps and mixers job includes

Finding the faultCamera, locator, thermal imager or gauge as the job needs, with what we find shown to you
Agreeing the costDiscussed on site before work begins, and written down for bigger jobs
The plumberLicensed in Victoria for the class of work involved, and insured
MaterialsWaterMark certified fittings and fixtures installed to the Australian Standards
PaperworkCompliance certificate for regulated work, plus photos or footage when useful
LeavingEverything tested with you, work area cleaned, old parts taken away

Asked and answered

Taps and Mixers in Ringwood: your questions

Can you fix a tap rather than replace it?

Usually. Washers, cartridges and spindles can be replaced in most taps.

Why does my mixer drip?

Usually a worn or damaged ceramic cartridge. We replace it with the right part for your model.

Can you fit tapware I have bought?

Yes, provided it is WaterMark certified and suits your connections.

Why does my tap bang when I turn it off?

This is often water hammer, linked to high pressure or loose pipes. We can test and fix it.

Do you fix garden taps?

Yes, including drips, leaks at the stem and cracked bodies.

How long does a tap repair take?

Most washer or cartridge repairs take well under an hour once we have the right part.

Quotes and bookings

Tell us about the job

Give us the basics and a licensed Ringwood plumber will phone you back. Water pouring somewhere it should not? Do not wait for a reply, ring 03 9088 4157.

03 9088 4157

There is no price list here on purpose. Every job is looked at first, and the cost is agreed with you before work starts.







    The process

    Four steps, no guesswork

    1. 1You ring or write

      Tell us what is happening and what sort of property it is. A phone photo of the problem or the hot water label helps us load the right parts.

    2. 2We look and explain

      On site we find the cause, show you what we see and settle the price with you. Nothing starts until you agree.

    3. 3The repair, tested

      Work is carried out to the plumbing code and the relevant Australian Standards, then run and checked with you watching.

    4. 4Tidy finish, written up

      Old parts leave with us, the area is cleaned and you get a written summary, with a certificate where the law requires one.

    Service area

    Ringwood first, then the Maroondah suburbs around it

    Most of our days start near Ringwood Lake and Eastland. From there it is a short hop north up Warrandyte Road to Ringwood North, Warranwood and Donvale, east along Maroondah Highway to Ringwood East, Croydon and Croydon Hills, south to Bayswater North, and west across the Whitehorse line into Mitcham. Not on the list? Ring 03 9088 4157 and we will tell you straight whether we can help.

    Plumbing trouble in Ringwood? Ring a plumber, not a call centre.